MUGEN SEIKI

This is the Mugen RIII Pro Starter Box for Off-Road Vehicles. FEATURES: Powered by two 540 motors Fully adjustable locating pins Rear handle design so that the placement of the glow starter does not...

This is the Front Anti Roll Bar 2.2mm for use on the Mugen MBX67 buggy. FEATURES:Metal construction INCLUDES:One Front Anti Roll Bar REQUIRES:Installation SPECS:Outer Diameter: 2.2mm

This is a Universal Joint Shaft Set for the Mugen MBX. Buggy. FEATURES:Metal constructionBlack in color INCLUDES:Two joint shafts for the Mugen MBXTwo 4mm set screws SPECS:Length: .39"...

This is the #650 Weight Super Silicone Shock Oil from Mugen. FEATURES:Will not thin out in hot weather or thicken up in cold weatherMay be used in any shock where this weight oil is required...

This is the electric powered, radio controlled, 1/8 scale Mugen MBX7-ECO M-Spec Off Road Buggy Kit. FEATURES: Chassis: A7075 T6 aluminum 0.12" (3mm) thick Drive: Four wheel three differential...

This is the 2.6mm Rear Anti Roll Bar for use on the Mugen 1/8 MBX6 Buggy Kit FEATURES: Steel construction INCLUDES: One 2.6mm Rear Anti Roll Bar REQUIRES:Installation on the vehicle SPECS:...

These are the replacement Clutch Springs for the Mugen MBX-4. These are located around the clutch shoes. This is a set of stock 1.0mm clutch springs. This is the most common clutch spring for the...

This is a pack of three optional Mugen Seiki 1.10mm Clutch Springs. These springs use 1.10mm thick wire, making them hard.  You can fine tune the way the clutch engages by using different...

Optional set of three Mugen Aluminum Clutch Shoes, and are intended for use with the Mugen MBX family of 1/8 scale vehicles. These clutch shoes can help the engine power be used more effectively and...

These shoes tend to hit harder than the black or white shoes with little slip. These shoes would be good for situations when the traction is very high. The most common spring used with the aluminum...

This is a package of 1.2mm 8H Taper Damper (shock) Pistons for the Mugen MBX7 and MBX6 Buggies. FEATURES: Plastic constructionEight 1.2mm holes per pistonInstalls inside piston, and with shock oil,...

Hop Up Mugen One Piece Engine Mount to use with the Mugen MBX5 and MBX7 1/8 scale buggies. This solid engine mount will help eliminate chassis flex around the engine mounting assembly on your buggy...

Mugen 1.0mm Clear Body, intended for use with the Mugen MBX7 1/8 scale nitro buggy.

MUGEN REPLACEMENT STONE GUARD SET FOR MBX7/MBX6/MBX6 ECO

MUGEN MBX7 CARBON FIBER REAR SHOCK TOWER.  - Made from 4mm carbon plate - Improved stability at the high grip or bumpy track.

This is a replacement Mugen Driveshaft Pin Tool Tip, and is intended for use with the Mugen Driveshaft Pin Replacement Tool  MUGE0541

MUGEN MBX7 ALUMINUM THROTTLE SERVO ARM. - Made from high quality A7075 aluminum.- Get more direct brake feeling and suitable for hot weather condition. This servo horn requires the Mugen Servo Horn...

This is the Mugen Seiki Fuel Tank w/Clunk: MBX7 (part #E2801) for the MBX7 1/8 off-road buggy.   This tank features an installed clunk and a rubber pull handle on the lid...

This is an optional Mugen 70mm Front Shock Spring Set, and is intended for use with the Mugen MBX7 1/8 scale nitro buggy. These 1.6 springs provide a softer feel to help tame the buggy. Many racers...

Mugen Seiki 70mm Front Shock Spring Set (Medium - 1.6/9.0T) (2) MBX7

Mugen Seiki 70mm Front Shock Spring Set Soft - 1.6/9.25t (2) Mbx7

Mugen Seiki 70mm Front Shock Spring Set X Soft - 1.6/9.5T (2)

Mugen Rear Shock Boots, and are intended for use with the Mugen MBX7 1/8 scale nitro buggy.

Mugen Front Shock Boots, and are intended for use with the Mugen MBX7 1/8 scale nitro buggy.

Mugen Servo Saver Set. This set includes the plastic steering racks that make up the servo saver.

Mugen Differential Case, intended for use with the Mugen MBX7 1/8 scale nitro buggy.

This plate adds durability and improves the steering response compared to the stock plastic plate. This package also includes mounting hardware.

Mugen Rear Lower Arm Hinge Pins, and are intended for use with the Mugen MBX7 1/8 scale nitro buggy.

This is a pair of Aluminum Rear Hub Carriers with Inserts for the Mugen MBX7 Buggy. FEATURES: Aluminum construction, gun metal gray in color INCLUDES: Left and Right Rear Hub Carriers (also known...

Mugen Graphite Front Hub Carrier Arm Mount Set, intended for use with the Mugen MBX7 1/8 scale nitro buggy. This set includes a left and right side mount.