INFERNO MP9 TKI2

The new "The Ring" muffler support is made in Ergal 7075 T6 in Italy, it can be mounted on all 1/10 and 1/8 Nitro models and will be available in 7 different colors. The muffler support will allow you to have 2 different configurations, fixed or mobile:-...

Produced in Ergal 7075 T6 with a thickness of 3mm and then anodized in different colors and marked with the RC-Project Logo.It is very light and resistant and will help to support the wing in case of violent impacts avoiding unpleasant deformations...

Elevate your racing performance with the JConcepts RM2 1/8 L.D. Razor Buggy Wing, designed for low drag, maximum stability, navigating tight corners and conquering big air jumps, this wing provides the edge you need to race faster, jump smoother, and...

Elevate your racing performance with the JConcepts RM2 1/8 L.D. Razor Buggy Wing, designed for low drag, maximum stability, navigating tight corners and conquering big air jumps, this wing provides the edge you need to race faster, jump smoother, and...

Complete Kit 3-Shoe Clutch with 1.00 springs. Ready to assemble and install on your nitro engine.

The RC-Project Clutch Bell Shim Kit is a set of shims designed to ensure the proper adjustment of the clutch bell. Here are the key features: - Outer diameter: 7 mm - Inner diameter: 5 mm The kit comes in a convenient box containing 20 pieces of each...

The emulsion screw seal has a rectangular cross-section with a small pocket aimed to facilitate and speed up operations, this will also ensure that the seal is not damaged during the disassembly process.   Fits the following brands that use our V2...

Honeycomb Bladders: the bladders have been completely redesigned to work inside the new Shock Caps. Volumes, sections and hardness have been re-designed to have almost zero-rebound during assembly, and to limit as much as possible the rebound gain that...

Honeycomb Bladders: the bladders have been completely redesigned to work inside the new Shock Caps. Volumes, sections and hardness have been re-designed to have almost zero-rebound during assembly, and to limit as much as possible the rebound gain that...

Bumpy Bladders: this new option was not present in the previous V1 and was a big surprise for our test drivers. It is an in-between emulsion and honeycomb: not suited for all conditions but where they worked the results in terms of performances were...

Bumpy Bladders: this new option was not present in the previous V1 and was a big surprise for our test drivers. It is an in-between emulsion and honeycomb: not suited for all conditions but where they worked the results in terms of performances were...

Bumpy Bladders: this new option was not present in the previous V1 and was a big surprise for our test drivers. It is an in-between emulsion and honeycomb: not suited for all conditions but where they worked the results in terms of performances were...

Honeycomb Bladders: the bladders have been completely redesigned to work inside the new Shock Caps. Volumes, sections and hardness have been re-designed to have almost zero-rebound during assembly, and to limit as much as possible the rebound gain that...

Complete Kit 3-Shoe Clutch with 0.95 springs. Ready to assemble and install on your nitro engine.

This is the Ultimate Racing Front Chassis Skid Plate for Kyosho 1/8 Off Road. Intended for the Kyosho MP9 and MP10 platforms, this front skid offers increased protection keeping your chassis safe from wear. Constructed from 0.5mm stainless steel...

This is the Ultimate Racing Rear Chassis Skid Plate for Kyosho 1/8 Off Road. Intended for the Kyosho MP9 and MP10 platforms, this rear skid offers increased protection keeping your chassis safe from wear. Constructed from 0.5mm stainless steel this...

Wing development is serious business and JConcepts has responded with a technically advanced alternative for 1/8th racing. The Razor polycarbonate wing features a brand-new design mimicking the injection molded Razor as closely as possible. Incorporating...

This is a set of 6 optional 70mm Front Shock Spring Set from Ultimate Racing. It’s intended for the majority 1/8 off road cars with 16mm shocks like Mugen, Kyosho, Losi, Sworkz, Xray, Mayako, etc. These shock springs allow you to...

This is a set of 6 optional 86mm Rear Shock Spring Set from Ultimate Racing. It’s intended for the majority 1/8 off road cars with 16mm shocks like Mugen, Kyosho, Losi, Sworkz, Xray, Mayako, etc. These shock springs allow you to...

ProTek RC 17mm Captured and Knurled Magnetic Wheel Nuts. Crafted with precision, these aluminum wheel nuts feature a knurled design for a secure grip on the wheels. Additionally, the option to install six set screws per nut allows them to become...

ProTek RC 17mm Captured and Knurled Magnetic Wheel Nuts. Crafted with precision, these aluminum wheel nuts feature a knurled design for a secure grip on the wheels. Additionally, the option to install six set screws per nut allows them to become...

The new "The Ring" muffler support is made in Ergal 7075 T6 in Italy, it can be mounted on all 1/10 and 1/8 Nitro models and will be available in 6 different colors. The muffler support will allow you to have 2 different configurations, fixed or mobile:-...

This is the V2 Low Center Gravity version of the 1.0mm 1/8 Rear Lexan Wing from Ultimate Racing. This rear wing provides less rotation than the V1 version in slow corners while improving stability in fast corners due to its reduced weight and lower...

Produced in Ergal 7075 T6 with a thickness of 3mm and then anodized in different colors and marked with the RC-Project Logo.It is very light and resistant and will help to support the wing in case of violent impacts avoiding unpleasant deformations...