JQ RACING

THE JQRacing 2.4mm Front Swaybar. Swaybars are a useful tool that can be used to change the balance of the car, and are used to adjust the car’s lateral grip. The basic setup for the...

THE JQRacing 2.6mm Rear Swaybar. Swaybars are a useful tool that can be used to change the balance of the car, and are used to adjust the car’s lateral grip. The basic setup for the...

THE JQRacing 2.8mm Rear Swaybar. Swaybars are a useful tool that can be used to change the balance of the car, and are used to adjust the car’s lateral grip. The basic setup for the...

JQ Racing 3.25° R-R Low D-Plate. This is the Rear/Rear "Low" type D-plate, or rear toe block, used on the JQ Black edition.

JQ Racing 2.75° R-R Low D-Plate. This is the Rear/Rear "Low" type D-plate, or rear toe block, used on the JQ Black edition.  

THE JQRacing CNC Servo Arm is compatible with any servo that uses a 23 tooth spline output shaft, for example Sanwa.

THE JQRacing One Piece Shock Holder/Aluminum Standoff set (4)

THE JQRacing CNC Servo Arm is compatible with any servo that uses a 24 tooth spline output shaft, for example Hitec.

THE JQRacing Servo Saver Part Set includes an aluminum servo saver tube, one servo saver spring, one servo saver tension nut, and one e-clip. JQ redesigned the servo saver on my car, to...

THE JQRacing Wingmount Set includes all the components needed to build one rear wing mount The original wingmount in 2011 had a weakspot where it could break. It wasn’t a big problem, so...

THE JQRacing Plastic Steering Parts include the left and right plastic parts for the steering bellcranks. These parts work with the original steering system, or the newer optional steering...

THE JQRacing Arm Holder Inserts are used to set the suspension arm geometry on THECar. There are three different inserts, and the set includes 4pcs of each. It is a good idea to replace...

THE JQRacing Fuel Tank Post Set includes 1 front and 1 rear post. These are the posts that are used to support the fuel tank and help isolate the fuel tank from vibration.

THE JQRacing Mounting Hardware for the One-Piece CNC Shock Caps, includes 4pcs, plastic shims and bushings, and steel bushings.

THE JQRacing Steering Links include all the plastic links for the steering system. They are compatible with all JQRacing 1:8th Buggies.

THE JQRacing Front Outer Hingepins

THE JQRacing Shock Plastic Parts includes all the plastic bits required to build any JQ 1:8th buggy shock, except the mounting hardware, which is differs depending on your model. It contains...

THE JQRacing Bumpers include the front and rear bumpers for THECar.

THE JQRacing Front/Rear Inner Hinge Pin Set includes two front and two rear hingepins. The hinge pins are installed in the suspension arms and secured by the hinge pin blocks, providing pivot...

THE JQRacing Air Filter Foam Set includes four inner air filters, and four outer air filters. Use high quality air filter oil, on both the inner and outer foams.

THE JQRacing 1.1mm Clutch Spring Set includes 3 springs. JQ preferred setup right now is 1×1.0 and 2×1.1 springs on my 3 shoe JQ clutch. This way I have a lot of power, yet the...

THE JQRacing Wing Shim Set includes two aluminium wing shims/buttons. (Black)

THE JQRacing Front Shock Shaft Set includes 2pcs front shafts. Silky smooth, and super hard!

THE JQRacing Rear Shock Shaft Set includes 2pcs Rear shafts. Silky smooth, and super hard! These shafts are Long length, they do work with the new Big Bore Rear Shocks.

THE JQRacing Hex Pin & Grubscrew Set includes four hex pins, and four grub screws. JQ decided to change the way the wheel hex is attached to the driveshaft. All other 1:8th Buggies have...

THE CNC Servo Arm for 2013 Radio Tray (Savox/Futaba) is compatible with any servo that uses a 25 tooth spline output shaft, for example Savox or Futaba.

THE CNC Servo Arm for 2013 Radio Tray (Sanwa) is compatible with any servo that uses a 23 tooth spline output shaft, for example Sanwa.

THE JQRacing CNC High Wingmount R (Black) raises the wing up higher, increasing stability specially at high speeds and while jumping. Definitely worth getting! You also need the Left...

THE JQRacing CNC High Wingmount L (Black) raises the wing up higher, increasing stability specially at high speeds and while jumping. Definitely worth getting! You also need the Left...

THE JQRacing 7075 Black Clutch Shoes with springs, 3pcs for 3-shoe clutch