JQ RACING

JQ Racing 3.25° R-R Low D-Plate. This is the Rear/Rear "Low" type D-plate, or rear toe block, used on the JQ Black edition.

JQ Racing 2.75° R-R Low D-Plate. This is the Rear/Rear "Low" type D-plate, or rear toe block, used on the JQ Black edition.  

THE JQRacing CNC Servo Arm is compatible with any servo that uses a 23 tooth spline output shaft, for example Sanwa.

THE JQRacing One Piece Shock Holder/Aluminum Standoff set (4)

THE JQRacing CNC Servo Arm is compatible with any servo that uses a 24 tooth spline output shaft, for example Hitec.

THE JQRacing Servo Saver Part Set includes an aluminum servo saver tube, one servo saver spring, one servo saver tension nut, and one e-clip. JQ redesigned the servo saver on my car, to...

THE JQRacing Wingmount Set includes all the components needed to build one rear wing mount The original wingmount in 2011 had a weakspot where it could break. It wasn’t a big problem, so...

THE JQRacing Plastic Steering Parts include the left and right plastic parts for the steering bellcranks. These parts work with the original steering system, or the newer optional steering...

THE JQRacing Arm Holder Inserts are used to set the suspension arm geometry on THECar. There are three different inserts, and the set includes 4pcs of each. It is a good idea to replace...

THE JQRacing Fuel Tank Post Set includes 1 front and 1 rear post. These are the posts that are used to support the fuel tank and help isolate the fuel tank from vibration.

THE JQRacing Steering Links include all the plastic links for the steering system. They are compatible with all JQRacing 1:8th Buggies.

THE JQRacing Shock Plastic Parts includes all the plastic bits required to build any JQ 1:8th buggy shock, except the mounting hardware, which is differs depending on your model. It contains...

THE JQRacing 1.1mm Clutch Spring Set includes 3 springs. JQ preferred setup right now is 1×1.0 and 2×1.1 springs on my 3 shoe JQ clutch. This way I have a lot of power, yet the...

THE JQRacing Rear Shock Shaft Set includes 2pcs Rear shafts. Silky smooth, and super hard! These shafts are Long length, they do work with the new Big Bore Rear Shocks.

THE JQRacing Hex Pin & Grubscrew Set includes four hex pins, and four grub screws. JQ decided to change the way the wheel hex is attached to the driveshaft. All other 1:8th Buggies have...

THE JQRacing CNC High Wingmount R (Black) raises the wing up higher, increasing stability specially at high speeds and while jumping. Definitely worth getting! You also need the Left...

THE JQRacing CNC High Wingmount L (Black) raises the wing up higher, increasing stability specially at high speeds and while jumping. Definitely worth getting! You also need the Left...

THE JQRacing 7075 Black Clutch Shoes with springs, 3pcs for 3-shoe clutch

THE JQRacing Shock Boot Set include 4pcs, to be used on the front or rear shocks. These shock boots are installed over the shock shafts and are held in place by a groove in the shock body and the...

THE JQRacing Rear Outer Hinge Pin Screws Set for the White Edition car, includes two hingepins and two M3 Nyloc nuts. These hinge pins feature a screw type design, that is secured with a lock nut...

THE JQRacing Fueltank, with O-Ring Seal, comes with the rubber grommets, and fuel line routing clips, as well as the L-shaped fueltube nipple. This is the current fueltank for all...

THE JQRacing 45/14 Front Crowngear part of THE Even Smoother gearing set.    

THE JQRacing Rear Gearbox, (also known as bulkhead) includes a sway bar holder, and also a rear differential bearing insert. The gearbox is installed on the rear of the chassis, and is the...

THE JQRacing Black Wing is arguably the sexiest wing on the market. Just look at it! We didn’t pre-drill holes in it so that anyone can add some style to their cars. As for the JQ Cars, we...