CUSTOM WORKS

Beach RC says...This is a Custom Works Wing & Side Panel Brace. This is a replacement for the Enforcer 7 and Outlaw 3 kits. Package includes one clear wing and side panel brace.  

Beach RC says...This is a pack of eight Custom Works M4 Serrated Flanged Wheel Nuts backed by an aggressive serrated surface for ultimate holding power. These nuts are used with 4mm axles, and...

Beach RC says... This is an optional Custom Works Brass Outer Pivot Arm, intended fro use with all Custom Works kits and most other 1/10 scale Dirt Oval cars. (Also fits TRA2370 arms for Slash...

MACHINED BLADES FOR ALUM OUTDRIVES (4)This is the best blade we offer and lasts multiple races provided you put a tad bit of diff lube on it prior to the race day. The blade type design allows the...

ADJUSTABLE ARM KIT FOR TLR 22SCTThese are for the original 22SCT not the 2.0. They can be used with the 22SCT 2.0 but you will need to use the rear hubs for the original 22SCT.This set will also fit...

ADJUSTABLE ARM KIT FOR ASSOCIATED SC10Allows quick and easy adjustment of Rear Toe Setting just by simply turning the included thumb screw. Very helpful for keeping up with changing track conditions...

NEW adjustable Toe Rear A-arms for the B6.1 and B6.1 Conversion cars.Custom Works Patented thumb screw adjustment makes these the easiest and fastest way to adjust your rear toe. Both sides capable...

Custom Works TrueSpeed machined spur gear.

Beach RC says... spur gears are available in a variety of sizes to tune your car for specific track conditions. Includes one 48 pitch spur.

Beach RC says... This is a replacement for the Intimidator 7, Enforcer 7, Outlaw 3 and Rocket Stage 3 kits. Includes ten shims.  New Part# CSW1255 

Beach RC says... This is  GSX MOTOR MOUNT SCREWS (4)  

each RC says... This is a replacement for the Enforcer 7 and Outlaw 3 kits. Includes one clear lexan front wing mount with factory applied overspray film. 

This is a  Custom Works X-tra short front suspenion arm for an Enforcer and Intimidator kit

Beach RC says... This is a brass weight that mounts on same hole centers as battery strap mounts so it can be mounted in any battery mount option holes or can be mounted below battery strap mount if...

New CVA collars for the cars using hex axles (Outlaw 4 and Rocket 4.) These can be installed to keep the cross pin from "escaping" from the assembly if the set screw comes loose. We will also be...

Custom Works Aluminum wing mount buttons anodized black (2)  

Custom Works Aluminum Short Servo Mounts. This is a replacement for the Enforcer 7 kits. Package includes two short aluminum servo mounts.   

Custom Works Front Axle. This is a replacement for the Intimidator 7, Enforcer 7, Outlaw 3 and Rocket Stage 3 kits. Package includes one axle, one spacer and one set screw.   

This is a replacement Custom Works Outlaw 4 Shorty Battery Strap, including both hook and loop sides. 

Custom Works 2-3/8" titanium turnbuckles (2)

Custom Works Steering Bellcrank Kit. This is a replacement for the Intimidator 7, Outlaw 3 and Rocket Stage 3 kits. Package includes the bellcrank, rod ends, ball studs, bearings, shims and hardware.

7" x 7" VORTEX SPRINT CAR TOP WING Comes with Mounts to fit all Sprint Cars kits using the V2 cage (#3430) This includes Outlaw 3 and 4 Enforcer 6 and 7 and most sprint car conversion kits for...

Custom Works RC DOMINATOR KIT FIberglass Chassis Kit.

Custom Works 4.5 x 3" Large Front Wing. This is a replacement for the Outlaw 3 kits. Package includes one clear clear front wing assembly with factory applied overspray film, and assembly hardware...

Custom Works Brass Spur Gear Hub

BRASS LOW PROFILE SERVO MOUNT

BRASS WEIGHT 1 OZ.

1.75OZ STEEL BATTERY WEIGHT

5MM REAR AXLE

CVA KIT (FITS OUTLAW 4 & ROCKET 4)