This is the 1/8 scale Glow Powered, Radio Controlled, 4WD Competition NB48.3 Buggy Kit from Tekno RC. **Engine Shown In Picture Is NOT Included.** New features compared to the original NB48 include: Redesigned Suspension Geometry Revised Chassis New Front and Rear Arms New Front and Rear Shock Towers & Mount Screws, & Revised Standoffs New Extra Long Shocks, Clamping Spring Perches w/Captured Shock Boots New Tapered Shock Pistons New Rear Hubs New Trailing Front Spindles and Spindle Carriers New V2 Hinge Pin Braces and Inserts Low Profile Wing Mount Revised Bumper for Increased Ground Clearance New Straight Turnbuckle Rod Ends New Easily Adjustable Droop Screws New Brake Linkage New 46T Spur Gear New Brake Pads and Discs Longer Rear Sway Bar Updated Setup Sheet for Improved Handling

FEATURES: Chassis: CNC machined hard anodized lightened 7075 aluminum, 0.16" (4mm) thick, short overhang for better bump handling and jump landing, adjustable brace system Drive: Four wheel with CV driveshafts and captured pins on wheels Clutch: Adjustable, four 7075 aluminum shoes Clutch Bell: 15T steel Fuel Tank: 4.2oz (125cc) Differentials: Three fluid filled adjustable lightweight diffs Suspension: Fully adjustable long travel, adjustable front arm sweep and angle, adjustable length rear arms, front and rear sway bars Steering: Ball bearing equipped, narrow pivot steering posts, adjustable steering stops for precise travel setting Shocks: 16mm bore CNC machined hard anodized threaded aluminum bodies, 4mm hardened steel polished shock shafts, CNC machine tapered pistons, CNC aluminum shock caps, preload adjusters and cartridge caps, Triple Guide Design for reduced shaft deflection, new clamping spring perches w/captured shock boots, options for vented cap, emulsion, or standard shock configurations Shock Towers: 0.197" (5mm) CNC Machined 7075 Aluminum Motor Mount: Dual position allows fast cornering or greater traction Brakes: Steel disc with semi-metallic pads Wing Mount: Adjustable, LCG lightweight Radio Tray: Integrated with right mud guard allowing receiver & battery to sit on chassis for lowest CG possible Throttle Control: CNC machined assembly riding on ball bearings Spur Gear: 46T Ackerman: Adjustable, Ackerman describes the effect of the inside front wheel turning faster than the outside front wheel during turns CNC aluminum Ackerman plate rides on 4 precision ball bearings Caster: Adjustable, caster/toe-in refers to the angle of the front suspension when viewed from the side of the car in relation to the chassis Camber: Adjustable front and rear, camber refers to the angle of the tops of the tires from vertical when viewed from front or behind vehicle

INCLUDES: NB48.3 Buggy Kit, Shock and Diff Oil, Threadlock, clear Body, 15T Clutch Bell, 46T Spur Gear, High-Downforce Wing, Decals, Shock and Diff Oil, Instructions

REQUIRES: Radio: 2-3ch with high-torque/speed steering & throttle servos Engine: .21 cu in (3.4cc) glow engine with tuned pipe Receiver Battery: Hump configuration Tires and Wheels: 1/8 scale buggy Starter box & glow igniter Polycarbonate safe spray or brush on paint Building and track equipment

SPECS: Vehicle; Length: 17.1" (435mm) without wing Width: 12-12.2" (306-310mm) Wheelbase: 12.7-13.2" (323-335mm) adjustable Dry Weight: 7.17lb (3260g), varies depending on equipment Diff Ratio: F/R-10t, center-46t RX Battery Box Dimensions: 2.3 x 1.4 x 1.3" (58.5 x 36 x 34.5mm) Body; Length: 13.4" (340mm) Width: 7.2" (183mm) Height: 4" (102mm)