LOSI

This is a pack of eight 4x8mm ball bearings from Losi. These are the wheel bearings.

Features Economical operation creates the best power per dollar availableLosi styling engine with excellent parts availability and carb selection due to commonality with the 454 and...

Optional Losi Adjustable Rear Hinge Pin Holder Set, and is intended for use with the Losi 810, TEN-T and TEN-SCTE.

Features _Ѣ 30% lighter than the stock outdrivesOverviewThese lightened outdrives are over 30% lighter than the stock units allowing for quicker acceleration.

Losi Differential Gear Set with Hardware, and is intended for use with the Losi Ten-T truck. This gear set is used in either the front, center or rear differentials. 

This is a replacement Losi Center/Front CV Driveshaft. This CV Driveshaft is used to connect the center differential to the front pinion gear that drives the front differential, allowing the...

This is a pack of two Losi Front Mini King Pin Tires, and are intended for use with the Losi Mini 8IGHT 1/14 Scale Buggy. Losi has been an innovator in off-road tire design for over 20 years and the...

This is a replacement Losi Front Wheel Set, and is intended for use with the Losi Mini-8IGHT.  

Losi Mini King Pin Pre-Mounted Front Tire Set, and is intended for use with the Losi Mini 8IGHT.

Uses one 5x10 and one 5x13mm bearing. These are available as a package under LOS6949 Clutch Bearing Set: 8B,8T or available separately under LOS6954 5x10 Shielded Ball Bearings (2) and LOSA6955 5 x...

Set of four replacement silver clutch springs for the Losi 8IGHT racing buggy. (30 deg .040" Clutch Spring) Spring chart: Silver: .040 wire with 30 degree angle Gold: .040 wire with 25 degree angle...

This is the 12X18X4MM BALL BEARING (LOSA6956)

Replacement Losi 8x14x4mm Flanged Rubber Sealed Ball Bearing

This is a pack of eight 10-32 low profile lock nuts from Losi.  

This is a pack of four replacement 10-32 x 3/8" oval point set screws from Losi.  

This is a pack of eight replacement 4mm rod ends for the Losi 8IGHT racing buggy.

Replacement Losi Center/Rear Drive Shaft. Note: For use in the TEN-SCTE 2.0, this is the center/front driveshaft.

Replacement Losi Brake Pad and Screw Set, and is intended for use with the Losi 8ight 2.0 1/8 Scale Buggy and Truggy.

Losi Brake Disc Set (2.0)

This is a replacement slipper friction pad from Losi. This friction pad goes between the spur gear and the slipper hub.

Differential Gear & Shaft Set: 22RTR and 22 series of vehicles.

This is a complete already assembled gear diff for the Losi 22 series of vehicles.

This is a replacement Losi 51 Tooth Differential Gear, and is intended for use with the Losi 22 RTR 1/10 buggy.  

Optional upgraded aluminum rear hub carriers for your 1/8 scale Losi and TLR vehicles.

Based on the ROAR-Championship-winning 8IGHT_†¢ buggy, this brushless power 4WD prodigy takes the mini 8IGHT platform to all new extremes. You_Ñéll be hard-pressed to find another...

Features Durable, aluminum, Race-proven TEN Platform Dynamite® Waterproof, 130A LiPo Compatible ESC Dynamite 4-Pole 3900Kv Brushless Motor Spektrum™ Waterproof SRS4200 Receiver with 2...

  15mm Shock Ends, Cups, Bushing: 8B/T 2.0/E, 8B/T 3.0/E  

Losi Aluminum Front Hinge Pin Brace Set

Overview Losi's Engine Accessory Set will work with .21 and .28 Nitro engines. The set includes spring wire clamps for the air cleaner and vinyl caps to seal the engine. The spring wire clamps...