JQ RACING

THE JQRacing CNC High Wingmount R (Gold) raises the wing up higher, increasing stability specially at high speeds and while jumping. Definitely worth getting! You also need the Left...

THE JQRacing Rear Hub Spacers include 4pcs of the 2mm spacers needed for setting the position of the rear hubs.

THE JQRacing Center Differential Outdrive Set includes two center differential outdrives with their pins. These out drive cups are installed in the center differential and are the part that...

JQ Products White Edition LV 7-Hole 1.3mm Flat 16mm Shock Pistons. These are the updated White Edition LV shock pistons that are used in the rear shocks with the stock setup but can be used in the...

This is a replacement JQRacing Easy Adjust Linkage Set in Black.

THE JQRacing Differential O-Ring Set includes 6 o-rings, enough for all three diffs. They are installed inside the differential cup, as well as on the ring and spur gears, and are used seal the...

THE JQRacing Lightweight 1mm Wider Hex with Nuts (2pcs). These wider hexes are a really good tuning part for the front end. Using these on the front increases steering, as well as front end...

THE JQRacing Differential Gear and Crosspin Set includes two sun gears, four planetary gears, all gear shims, and two cross pins.

THE JQRacing Universal Centre Shaft 86mm, is intended for use in the front centre, when the centre diff is mounted in the mid to front positions. If you are running the centre diff towards the...

THE JQRacing 86mm Center Dogbone, for the front, with the centre diff set in the mid to front positions. Aluminium dogbones make the drivetrain as light as possible, one of our goals with the...

This is a replacement JQ Products Black Edition #1 2.0 Ackermann Plate. Package includes one #1 2.0 ackermann plate. These are compatible with the Black and White Edition models.  

THE JQRacing 2.4mm Front Swaybar. Swaybars are a useful tool that can be used to change the balance of the car, and are used to adjust the car’s lateral grip. The basic setup for the...

THE JQRacing 2.8mm Rear Swaybar. Swaybars are a useful tool that can be used to change the balance of the car, and are used to adjust the car’s lateral grip. The basic setup for the...

JQ Racing 3.25° R-R Low D-Plate. This is the Rear/Rear "Low" type D-plate, or rear toe block, used on the JQ Black edition.

JQ Racing 2.75° R-R Low D-Plate. This is the Rear/Rear "Low" type D-plate, or rear toe block, used on the JQ Black edition.  

THE JQRacing CNC Servo Arm is compatible with any servo that uses a 23 tooth spline output shaft, for example Sanwa.

THE JQRacing One Piece Shock Holder/Aluminum Standoff set (4)

THE JQRacing CNC Servo Arm is compatible with any servo that uses a 24 tooth spline output shaft, for example Hitec.

THE JQRacing Servo Saver Part Set includes an aluminum servo saver tube, one servo saver spring, one servo saver tension nut, and one e-clip. JQ redesigned the servo saver on my car, to...

THE JQRacing Wingmount Set includes all the components needed to build one rear wing mount The original wingmount in 2011 had a weakspot where it could break. It wasn’t a big problem, so...

THE JQRacing Plastic Steering Parts include the left and right plastic parts for the steering bellcranks. These parts work with the original steering system, or the newer optional steering...

THE JQRacing Arm Holder Inserts are used to set the suspension arm geometry on THECar. There are three different inserts, and the set includes 4pcs of each. It is a good idea to replace...

THE JQRacing Steering Links include all the plastic links for the steering system. They are compatible with all JQRacing 1:8th Buggies.

THE JQRacing Shock Plastic Parts includes all the plastic bits required to build any JQ 1:8th buggy shock, except the mounting hardware, which is differs depending on your model. It contains...

THE JQRacing 1.1mm Clutch Spring Set includes 3 springs. JQ preferred setup right now is 1×1.0 and 2×1.1 springs on my 3 shoe JQ clutch. This way I have a lot of power, yet the...

THE JQRacing Rear Shock Shaft Set includes 2pcs Rear shafts. Silky smooth, and super hard! These shafts are Long length, they do work with the new Big Bore Rear Shocks.

THE JQRacing Hex Pin & Grubscrew Set includes four hex pins, and four grub screws. JQ decided to change the way the wheel hex is attached to the driveshaft. All other 1:8th Buggies have...

THE JQRacing CNC High Wingmount R (Black) raises the wing up higher, increasing stability specially at high speeds and while jumping. Definitely worth getting! You also need the Left...

THE JQRacing CNC High Wingmount L (Black) raises the wing up higher, increasing stability specially at high speeds and while jumping. Definitely worth getting! You also need the Left...

THE JQRacing 7075 Black Clutch Shoes with springs, 3pcs for 3-shoe clutch